MC73110 Motor Control Chip

首頁
向上
Contact Us 聯繫我們
Amphenol 軍規接頭 軍用接頭 軍規電纜 軍用電纜 各式特殊電纜製作
CCC 馬達控制
Datel 資料擷取模組
IOtech 專業量測儀器
MccDaq 資料擷取
PDI 振盪器/濾波器
Recom電源轉換器
Semtech 軍規二極體
Ultravolt 高壓電源
智慧電網 IEC 61850
學生套件
產品型錄查詢
Buy Stock 庫存出清

MC73110 FOR BRUSHLESS DC MOTOR CONTROL

Brushless DC Motor Controller DOCUMENTATION

Features:

  • Controls 3-phase brushless DC motors
  • High performance digital current loop
  • Velocity loop with encoder or tachometer feedback
  • Internal velocity profile generator
  • Sinusoidal or 6-step commutation
  • Field oriented control
  • Hall sensor inputs
  • 6-signal PWM output with shoot-through protection
  • Direct analog signal input
  • Serial port up to 416 Kbaud
  • Quadrature encoder input up to 10 Mcounts/sec
  • Serial EEProm or onboard flash configuration load
  • High speed index input & capture
  • SPI (synchronous serial interface) command input
  • Emergency stop input
  • 10 kHz velocity loop & commutation rate
  • 20 kHz PWM output rate
  • Compact 64-pin plastic quad flat pack (PQFP)

Product Description:

The MC73110 Motor Control IC provides high performance digital current loop, velocity loop, and commutation, for brushless DC motors. This intelligent single-axis drive controller operates in internal velocity profile mode, velocity mode with an external velocity command signal, or torque mode with an external torque command signal. The MC73110 can be operated standalone, using pre-programmed flash-stored parameters, or through the serial port using microprocessor-style commands.

The current loop provides software-programmable P and I terms as well as other parameters such as shoot-through protection timing. Two symmetric 3-phase PWM (pulse width modulated) output modes are provided, 6-signal mode and 3-signal mode. Two direct-input analog signals provide current feedback from the drive. Commutation is software-programmable, and can occur using a six-step waveform or using a sinusoidal waveform. Velocity feedback is provided by the quadrature encoder, or via a direct-input analog tachometer signal. Velocity commands are provided by an internal profile generator, by a digital SPI 16-bit data stream, or by direct-input analog signal. A programmable compensation filter closes the loop and determines the motor command.

With over 130 commands, the Magellan Motion Processors provide a flexible and powerful instruction set to initialize and control the motion application, monitor ongoing performance, and synchronize overall machine behavior. Working with the Magellan devices, PMD’s powerful Pro-Motion® GUI makes it easy to graph and analyze system performance, while C-Motion® allows you to develop your own application using C/C++.

To create a complete motion controller, the MC73110 is connected to three half-bridge amplifiers, typically MOSFET or IGBT-based. The MC73110 is packaged in a compact 64-pin PQFP (plastic quad flat pack), and operates from 3.3 V. 

[首頁] [向上] [Contact Us 聯繫我們] [Amphenol 軍規接頭 軍用接頭 軍規電纜 軍用電纜 各式特殊電纜製作] [CCC 馬達控制] [Datel 資料擷取模組] [IOtech 專業量測儀器] [MccDaq 資料擷取] [PDI 振盪器/濾波器] [Recom電源轉換器] [Semtech 軍規二極體] [Ultravolt 高壓電源] [智慧電網 IEC 61850] [學生套件] [產品型錄查詢] [Buy Stock 庫存出清]


    

新 北 市 汐 止 區 康 寧 街 169 巷 23 號 7 樓 之 一

公司電話:+886-2-2695-8906(代表號)

 02-2695-6755, 02-2695-7011, 02-2695-7033

公司傳真:+886-2-26958911

上次更新日期: 2015年07月03日。